Configuring Rapid PVST+

-

 

Tugas Pertemuan 5 (Administrasi Jaringan - 12.5B.05)
NAMA : RUDIYANTO
NIM : 12180061




  1. Tempatkan 3 buah Switch dan 3 buah PC


  2. Menghubungkan ketiga Switch menggunakan kabel Cross


  3. Hubungkan Switch (S2) & ketiga komputer menggunakan kabel Straight




  4. Setting IP Address PC0, PC1, PC2

    5. Alamat IP

    PC0: 172.17.10.21
    PC1: 172.17.20.22
    PC2: 172.17.30.23


  5. Konfigurasi Switch


  1. Konfigurasi Switch 1
    2. S1>enable
    S1#configure terminal
    S1(config)#vlan 10
    S1(config-vlan)#vlan 20
    S1(config-vlan)#vlan 30
    S1(config-vlan)#vlan 40
    S1(config-vlan)#vlan 50
    S1(config-vlan)#vlan 60
    S1(config-vlan)#vlan 70
    S1(config-vlan)#vlan 80
    S1(config-vlan)#vlan 99
    S1(config-vlan)#exit
    S1(config)#int range f0/1-4
    S1(config-if-range)#switchport mode trunk
    S1(config-if-range)#switch trunk native vlan 99
    S1(config-if-range)#exit
    S1(config)#interface vlan 99
    S1(config-if)#ip address 172.17.10.21 255.255.255.0
    S1(config-if)#exit
    S1(config)#spanning-tree mode rapid-pvst
    S1(config)#spanning-tree vlan 1,10,30,50,70 root primary

  2. Konfigurasi Switch 2
    3. S2>enable
    S2#configure terminal
    S2(config)#vlan 10
    S2(config-vlan)#vlan 20
    S2(config-vlan)#vlan 30
    S2(config-vlan)#vlan 40
    S2(config-vlan)#vlan 50
    S2(config-vlan)#vlan 60
    S2(config-vlan)#vlan 70
    S2(config-vlan)#vlan 80
    S2(config-vlan)#vlan 99
    S2(config-vlan)#exit
    S2(config)#interface f0/6
    S2(config-if)#switchport access vlan 30
    S2(config-if)#interface f0/11
    S2(config-if)#switchport access vlan 10
    S2(config-if)#interface f0/18
    S2(config-if)#switchport access vlan 20
    S2(config-if)#exit
    S2(config)#interface range f0/1-4
    S2(config-if-range)#switchport mode trunk
    S2(config-if-range)#exit
    S2(config)#interface vlan 99
    S2(config-if)#ip address 172.17.20.22 255.255.255.0
    S2(config-if)#exit
    S2(config)#spanning-tree mode rapid-pvst
    S2(config)#spanning-tree vlan 1,10,20,30,40,50,60,70,80,99 root secondary
    S2(config)#interface range f0/6, f0/11, f0/18
    S2(config-if-range)#switchport mode access
    S2(config-if-range)#spanning-tree portfast
    S2(config-if-range)#spanning-tree bpduguard enable
    S2(config-if-range)#no shutdown

  3. Konfigurasi Switch 3
    4. S3>enable
    S3#configure terminal
    S3(config)#vlan 10
    S3(config-vlan)#vlan 20
    S3(config-vlan)#vlan 30
    S3(config-vlan)#vlan 40
    S3(config-vlan)#vlan 50
    S3(config-vlan)#vlan 60
    S3(config-vlan)#vlan 70
    S3(config-vlan)#vlan 80
    S3(config-vlan)#vlan 99
    S3(config-vlan)#exit
    S3(config)#interface range f0/1-4
    S3(config-if-range)#switchport mode trunk
    S3(config-if-range)#switchport trunk native vlan 99
    S3(config-if-range)#exit
    S3(config)#interface vlan 99
    S3(config-if)#ip address 172.17.30.23 255.255.255.0
    S3(config-if)#exit
    S3(config)#spanning-tree mode rapid-pvst
    S3(config)#spanning-tree vlan 20,40,60,80,99 root primary

  4. Hasil yang sudah terkonfigurasikan




Comments

Post a Comment